Spoke Machine
The Phil Wood Spoke Cutting and Threading Machine is designed and manufactured to provide an invaluable tool to manually size, cut, and place a factory-quality thread on a spoke within a few seconds. The thread is rolled/cold forged onto the spoke, which does not remove material as would occur if the thread were cut into the spoke.
The machine performs through the operation of a manual crank. One revolution of the machine handle both cuts and threads the spoke. It is designed to cut and thread 1.8 mm (15 ga.), 2.0 mm (14 ga.), 2.3 mm (13 ga.) and 2.6 mm (12 ga.) spokes and place 10 mm of 56 tpi thread on the end of each spoke. Please note: Spacers to set the machine to cut 2.3mm (13 ga) and 2.6mm (12 ga) are available, but are not offered as a standard accessory included with the machine.
Our machine is capable of cutting carbon steel, stainless steel, titanium, anodized, and powder coated spokes. Butted and aero spokes can be cut and threaded on the full diameter portion of the spoke. Please be sure to thoroughly clean your machine and dies after cutting and threading powder coated spokes.
The spoke machine die set has two surfaces for cold forging rolled threads onto a spoke. If properly maintained, each surface can roll 60,000 spokes, for a total of 120,000 spokes on a single die set. When cutting and threading standard spokes, some die sets have reached upwards of 160,000 spokes. Lubrication with Phil Tenacious Oil is recommended during the cutting and threading process, applied to the dies every 20 - 30 operations.
ACCESSORIES INCLUDED WITH THE PURCHASE OF A NEW MACHINE
Spoke Holder - Long
1.8 mm and 2.0 mm Setup Spacer
Spoke Gage & Length Measure Scale
6" California Bicycle Products Group Scale
Spoke Cutting & Threading Machine Manual
Hex Wrench Set: 1/4", 5/32", 3/16" and 5/16"
Protective Eyewear
4 oz Bottle of Phil Tenacious Oil
16 oz Tub of Phil Hand Cleaner
INSTRUCTIONS
Spoke Machine Instructions (pdf)
The machine performs through the operation of a manual crank. One revolution of the machine handle both cuts and threads the spoke. It is designed to cut and thread 1.8 mm (15 ga.), 2.0 mm (14 ga.), 2.3 mm (13 ga.) and 2.6 mm (12 ga.) spokes and place 10 mm of 56 tpi thread on the end of each spoke. Please note: Spacers to set the machine to cut 2.3mm (13 ga) and 2.6mm (12 ga) are available, but are not offered as a standard accessory included with the machine.
Our machine is capable of cutting carbon steel, stainless steel, titanium, anodized, and powder coated spokes. Butted and aero spokes can be cut and threaded on the full diameter portion of the spoke. Please be sure to thoroughly clean your machine and dies after cutting and threading powder coated spokes.
The spoke machine die set has two surfaces for cold forging rolled threads onto a spoke. If properly maintained, each surface can roll 60,000 spokes, for a total of 120,000 spokes on a single die set. When cutting and threading standard spokes, some die sets have reached upwards of 160,000 spokes. Lubrication with Phil Tenacious Oil is recommended during the cutting and threading process, applied to the dies every 20 - 30 operations.
ACCESSORIES INCLUDED WITH THE PURCHASE OF A NEW MACHINE
Spoke Holder - Long
1.8 mm and 2.0 mm Setup Spacer
Spoke Gage & Length Measure Scale
6" California Bicycle Products Group Scale
Spoke Cutting & Threading Machine Manual
Hex Wrench Set: 1/4", 5/32", 3/16" and 5/16"
Protective Eyewear
4 oz Bottle of Phil Tenacious Oil
16 oz Tub of Phil Hand Cleaner
INSTRUCTIONS
Spoke Machine Instructions (pdf)
